DataSheetWiki


FP2189-PCB900S fiches techniques PDF

ETC - high performance 1-Watt HFET (Heterostructure FET) in a low-cost SOT-89 surfacemount

Numéro de référence FP2189-PCB900S
Description high performance 1-Watt HFET (Heterostructure FET) in a low-cost SOT-89 surfacemount
Fabricant ETC 
Logo ETC 





1 Page

No Preview Available !





FP2189-PCB900S fiche technique
FP2189
1 Watt HFET
The Communications Edge TM
Preliminary Product Information
Product Features
50 – 4000 MHz
Up to +31 dBm P1dB
Up to +45 dBm Output IP3
High Drain Efficiency
19 dB Gain @ 900 MHz
MTBF >100 Years
SOT-89 SMT Package
Product Description
The FP2189 is a high performance 1-Watt HFET
(Heterostructure FET) in a low-cost SOT-89 surface-
mount package. This device works optimally at a drain
bias of +8 V and 250 mA to achieve +45 dBm output
IP3 performance and an output power of +31 dBm at
1-dB compression.
The device conforms to WJ Communications’ long
history of producing high reliability and quality
components. The FP2189 has an associated MTBF of
greater than 100 years at a mounting temperature of
85°C. All devices are 100% RF & DC tested.
The product is targeted for use as driver amplifiers for
wireless infrastructure where high performance and high
efficiency are required.
Functional Diagram
4
12
Function
Input
Ground
Output/Bias
Ground
3
Pin No.
1
2
3
4
Specifications
DC Electrical Parameter Units Min Typ Max
Saturated Drain Current1, Idss
Transconductance, Gm
Pinch Off Voltage2, Vp
mA
mS
V
500
350
-2.0
Parameters3
Units Min Typ Max
Frequency Range
Small Signal Gain, Gss
Output P1dB
Output IP34
Thermal Resistance
MHz
dB
dBm
dBm
°C/W
50
4000
15
+31
+45
30
1. Idss is measured with Vgs = 0 V, Vds = 3 V.
2. Pinch-off voltage is measured when Ids = 0.4 mA.
3. Test conditions unless otherwise noted: T = 25ºC, VDS = 8 V, IDQ = 250 mA, frequency = 900 MHz
in an application circuit with ZL = ZLOPT, ZS = ZSOPT .
4. 3OIP measured with two tones at an output power of +15 dBm/tone separated by 1 MHz. The
suppression on the largest IM3 product is used to calculate the 3OIP using a 2:1 rule.

Absolute Maximum Ratings
Parameters
Operating Case Temperature
Storage Temperature
Maximum DC Power
RF Input Power (continuous)
Rating
-40 to +85 °C
-40 to +125 °C
4.0 W
+20 dBm
Operation of this device above any of there parameters may cause permanent damage
Typical Parameters5
Parameter Units
Typical
Frequency
S21
S11
S22
Output P1dB
Output IP3
Noise Figure
Vdd
Idq6
Idd at P1dB
MHz
dB
dB
dB
dBm
dBm
dB
V
mA
mA
915
19.1
-17
-10
+30.3
+44.3
4.2
+8
250
260
1960
15.2
-16
-8
+30.8
+44.2
3.5
+8
250
330
2140
13.8
-23
-9
+31.4
+45.5
4.5
+8
250
320
5. Typical parameters represent performance in an application circuit.
6. Idq is the quiescent drain current at small signal output levels. The
current may increase as the output power is increased near its
compression point.
Ordering Information
Part No.
FP2189
FP2189-PCB900S
FP2189-PCB1900S
FP2189-PCB2140S
Description
1-Watt HFET
(Available in Tape & Reel)
900 MHz Application Circuit
1900 MHz Application Circuit
2140 MHz Application Circuit
This document contains information on a new product.
Specifications and information are subject to change without notice
WJ Communications, Inc Phone 1-800-WJ1-4401 FAX: 408-577-6620 e-mail: [email protected] Web site: www.wj.com
May 2002

PagesPages 6
Télécharger [ FP2189-PCB900S ]


Fiche technique recommandé

No Description détaillée Fabricant
FP2189-PCB900S high performance 1-Watt HFET (Heterostructure FET) in a low-cost SOT-89 surfacemount ETC
ETC

US18650VTC5A

Lithium-Ion Battery

Sony
Sony
TSPC106

PCI Bus Bridge Memory Controller

ATMEL
ATMEL
TP9380

NPN SILICON RF POWER TRANSISTOR

Advanced Semiconductor
Advanced Semiconductor


www.DataSheetWiki.com    |   2020   |   Contactez-nous  |   Recherche