DS2409 Datasheet PDF - Dallas Semiconducotr
| Part Number | DS2409 | |
| Description | MicroLAN Coupler | |
| Manufacturers | Dallas Semiconducotr | |
| Logo |  |
|
|
There is a preview and DS2409 download ( pdf file ) link at the bottom of this page. Total 18 Pages | ||
Preview 1 page No Preview Available !
www.maxim-ic.com
FEATURES
§ Low impedance coupler to create large
common-ground, multi-level MicroLAN
networks
§ Keeps inactive branches pulled high to 5V
§ Simplifies network topology analysis by
logically decoupling devices on active
network segments
§ Conditional search for fast-event signaling
§ Auxiliary 1-Wire® line to connect a memory
chip or to be used as digital input
§ Programmable, general-purpose open-drain
control output
§ Communicates at 16.3kbits per second
§ Unique, factory-lasered and tested 64-bit
registration number (8-bit family code + 48-
bit serial number + 8-bit CRC tester) assures
absolute traceability because no two parts are
alike
§ 8-bit family code specifies device
communication requirements to bus master
§ Built-in multidrop controller ensures
compatibility with other MicroLAN products
§ Operating temperature range from -40°C to
+85°C
§ Compact, low-cost 6-pin TSOC surface
mount package
DS2409
MicroLAN Coupler
PIN ASSIGNMENT
16
25
34
TOP VIEW
3.7mm X 4.0mm X 1.5 mm
SIDE VIEW
6-PIN TSOC PACKAGE
PIN DESCRIPTION
Pin 1
GND
Pin 2
1-Wire in
Pin 3
Main 1-Wire out
Pin 4
Auxiliary 1-Wire out
Pin 5
Control Output
Pin 6
VDD
ORDERING INFORMATION
DS2409P
6-pin TSOC package
DS2409P/T&R
Tape and Reel of DS2409P
DESCRIPTION
The MicroLAN coupler is an essential component to build and control 1-Wire MicroLAN networks with
multi-level branching. In contrast to approaches that switch the ground line, the coupler maintains a
common ground level for the whole network and keeps the inactive segments powered. This simplifies
supplying central or local power for additional circuitry and prevents loss of status of parasitically
powered devices. It also avoids disrupting communication caused by the parasitic power supply of 1-Wire
devices after activating a branch. The coupler does not contain any user-programmable memory. To label
a branch, one can connect any 1-Wire memory device to the auxiliary 1-Wire output of the coupler. Both
the main and the auxiliary 1-Wire output are supported by a “smart-on” command. This command
generates a reset/presence sequence on the selected output before the electronic switch closes the contact
to the 1-Wire bus. This way the bus master can apply a ROM function command (optionally followed by
a memory function) to the devices on the just activated segment with all other devices in the network
1 of 18
061907
|
| |
 
STATUS CONTROL BYTE Table 1
7654
DATA
X
CNTR.
SEL.
MODE
R/ W
3
R/ W
2
X
DS2409
10
XX
0-2 X don’t care
3-4 R/ W Write control: both bits must be 0 to change the status.
5 MODE control output mode selection: 0 = auto-control mode (default), 1 = manual mode
6
CNTR.
SEL.
control output association (auto-control mode): 0 = main (default), 1 = auxiliary
7
DATA
X
Value to be written to control output (manual mode only): don’t care otherwise
STATUS INFO BYTE Table 2
765
MODE
CNTR.
STAT
EVNT
AUX.
4
EVNT
MAIN
3
AUX.
LEVL
2
AUX.
STAT
1
MAIN
LEVL
0
MAIN
STAT
0
MAIN
STAT
status of main output: 0 = active (connected to bus master), 1 = inactive
1
MAIN
LEVL
voltage sensed at main output: 0 = low, 1 = high (see note)
2
AUX.
STAT
status of auxiliary output: 0 = active (connected to bus master), 1 = inactive
3
AUX.
LEVL
voltage sensed at auxiliary output: 0 = low, 1 = high (see note)
4
EVNT
MAIN
event flag for main output: 0 = no event, 1 = negative edge sensed since inactive
5
EVNT
AUX.
event flag for aux. Output: 0 = no event, 1 = negative edge sensed since inactive
6
CNTR. if auto-control mode: control output association, 0 = main, 1 = auxiliary
STAT if manual mode: 0 = output transistor off, 1 = output transistor on
7 MODE control output mode: 0 = auto-control mode, 1 = manual mode
NOTE:
Data is valid only if the output is decoupled from the 1-Wire input.
ALL LINES OFF [66h]
This command is used to deactivate the currently active 1-Wire output and to clear both event flags or to
end a discharge cycle initiated by the Discharge Lines command. Before issuing this command, one
should read the status and check the event flags of both, the main and the auxiliary output. Otherwise one
might inadvertently clear the event flag without having taken appropriate action. If the DS2409 is in auto-
control mode, the transistor at the control output will be switched off (non-conducting). At power-on, the
device will automatically perform the All Lines Off command. In contrast to a power-on cycle, the All
Lines Off command does not clear the Mode and Control Select bits.
5 of 18
Preview 5 Page |
Part DetailsOn this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for DS2409 electronic component. |
| Information | Total 18 Pages | |
| Link URL | [ Copy URL to Clipboard ] | |
| Download | [ DS2409.PDF Datasheet ] | |
Share Link :
Electronic Components Distributor
|
An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists. |
| SparkFun Electronics | Allied Electronics | DigiKey Electronics | Arrow Electronics |
| Mouser Electronics | Adafruit | Newark | Chip One Stop |
Featured Datasheets
| Part Number | Description | MFRS |
| DS2401 | The function is Silicon Serial Number. Dallas Semiconducotr | |
| DS2401 | The function is Silicon Serial Number. Maxim Integrated |  |
| DS2404 | The function is EconoRAM Time Chip. Dallas Semiconducotr | |
Semiconductors commonly used in industry:
1N4148 |
BAW56 |
1N5400 |
NE555 | | ||
Quick jump to:
DS24
1N4
2N2
2SA
2SC
74H
BC
HCF
IRF
KA | ||