|
|
PDF LV2209MMBV2109LT1 Data sheet ( Hoja de datos )
| Número de pieza | LV2209MMBV2109LT1 | |
| Descripción | Silicon Tuning Diodes | |
| Fabricantes | ON Semiconductor | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de LV2209MMBV2109LT1 (archivo pdf) en la parte inferior de esta página. Total 8 Páginas | ||
|
No Preview Available !
MMBV2101LT1 Series,
MV2105, MV2101, MV2109,
LV2205, LV2209
Silicon Tuning Diodes
6.8–100 pF, 30 Volts
Voltage Variable Capacitance Diodes
These devices are designed in popular plastic packages for the high
volume requirements of FM Radio and TV tuning and AFC, general
frequency control and tuning applications. They provide solid–state
reliability in replacement of mechanical tuning methods. Also
available in a Surface Mount Package up to 33 pF.
• High Q
• Controlled and Uniform Tuning Ratio
• Standard Capacitance Tolerance – 10%
• Complete Typical Design Curves
MAXIMUM RATINGS
Rating
Symbol
Reverse Voltage
VR
Forward Current
IF
Forward Power Dissipation
@ TA = 25°C
Derate above 25°C
MMBV21xx
PD
Value
30
200
225
1.8
Unit
Vdc
mAdc
mW
mW/°C
@ TA = 25°C
Derate above 25°C
MV21xx
LV22xx
Junction Temperature
Storage Temperature Range
TJ
Tstg
DEVICE MARKING
MMBV2101LT1 = M4G
MMBV2103LT1 = 4H
MMBV2105LT1 = 4U
MMBV2107LT1 = 4W
MMBV2108LT1 = 4X
MMBV2109LT1 = 4J
MV2101 = MV2101
MV2105 = MV2105
280
2.8
+150
–55 to +150
°C
°C
MV2109 = MV2109
LV2205 = LV2205
LV2209 = LV2209
ELECTRICAL CHARACTERISTICS (TA = 25°C unless otherwise noted)
Characteristic
Symbol Min Typ Max Unit
Reverse Breakdown Voltage
V(BR)R
Vdc
(IR = 10 µAdc)
MMBV21xx, MV21xx
30 –
–
LV22xx
25 –
–
Reverse Voltage Leakage
Current
(VR = 25 Vdc, TA = 25°C)
Diode Capacitance
Temperature Coefficient
(VR = 4.0 Vdc, f = 1.0 MHz)
IR – – 0.1 µAdc
TCC
– 280 – ppm/°C
http://onsemi.com
31
Cathode
Anode
SOT–23
21
Cathode
Anode
TO–92
MARKING
DIAGRAM
3
1
2
TO–236AB, SOT–23
CASE 318–08
STYLE 8
XXX M
XXX = Device Code*
M = Date Code
* See Table
1
2
TO–226AC, TO–92
CASE 182
STYLE 1
XX
XXXX
YWW
XX = Device Code Line 1*
XXXX = Device Code Line 2*
M = Date Code
* See Table
Preferred devices are recommended choices for future use
and best overall value.
© Semiconductor Components Industries, LLC, 2001
October, 2001 – Rev. 3
1
Publication Order Number:
MMBV2101LT1/D
1 page  
MMBV2101LT1 Series, MV2105, MV2101, MV2109, LV2205, LV2209
SOLDER STENCIL GUIDELINES
Prior to placing surface mount components onto a printed
circuit board, solder paste must be applied to the pads. A
solder stencil is required to screen the optimum amount of
solder paste onto the footprint. The stencil is made of brass
or stainless steel with a typical thickness of 0.008 inches.
The stencil opening size for the surface mounted package
should be the same as the pad size on the printed circuit
board, i.e., a 1:1 registration.
TYPICAL SOLDER HEATING PROFILE
For any given circuit board, there will be a group of
control settings that will give the desired heat pattern. The
operator must set temperatures for several heating zones,
and a figure for belt speed. Taken together, these control
settings make up a heating “profile” for that particular
circuit board. On machines controlled by a computer, the
computer remembers these profiles from one operating
session to the next. Figure 7 shows a typical heating profile
for use when soldering a surface mount device to a printed
circuit board. This profile will vary among soldering
systems but it is a good starting point. Factors that can
affect the profile include the type of soldering system in
use, density and types of components on the board, type of
solder used, and the type of board or substrate material
being used. This profile shows temperature versus time.
The line on the graph shows the actual temperature that
might be experienced on the surface of a test board at or
near a central solder joint. The two profiles are based on a
high density and a low density board. The Vitronics
SMD310 convection/infrared reflow soldering system was
used to generate this profile. The type of solder used was
62/36/2 Tin Lead Silver with a melting point between
177–189°C. When this type of furnace is used for solder
reflow work, the circuit boards and solder joints tend to
heat first. The components on the board are then heated by
conduction. The circuit board, because it has a large surface
area, absorbs the thermal energy more efficiently, then
distributes this energy to the components. Because of this
effect, the main body of a component may be up to 30
degrees cooler than the adjacent solder joints.
200°C
150°C
100°C
STEP 1
PREHEAT
ZONE 1
RAMP"
STEP 2
VENT
SOAK"
STEP 3
HEATING
ZONES 2 & 5
RAMP"
STEP 4
STEP 5
HEATING HEATING
ZONES 3 & 6 ZONES 4 & 7
SOAK"
SPIKE"
DESIRED CURVE FOR HIGH
MASS ASSEMBLIES
160°C
170°C
150°C
STEP 6 STEP 7
VENT COOLING
205° TO 219°C
PEAK AT
SOLDER JOINT
100°C
140°C
SOLDER IS LIQUID FOR
40 TO 80 SECONDS
(DEPENDING ON
MASS OF ASSEMBLY)
DESIRED CURVE FOR LOW
MASS ASSEMBLIES
50°C
TIME (3 TO 7 MINUTES TOTAL)
TMAX
Figure 6. Typical Solder Heating Profile
http://onsemi.com
5
5 Page | ||
| Páginas | Total 8 Páginas | |
| PDF Descargar | [ Datasheet LV2209MMBV2109LT1.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| LV2209MMBV2109LT1 | Silicon Tuning Diodes | ON Semiconductor |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |