DataSheetWiki


3059 fiches techniques PDF

Allegro MicroSystems - HALL-EFFECT GEAR-TOOTH SENSORS -AC COUPLED

Numéro de référence 3059
Description HALL-EFFECT GEAR-TOOTH SENSORS -AC COUPLED
Fabricant Allegro MicroSystems 
Logo Allegro MicroSystems 





1 Page

No Preview Available !





3059 fiche technique
3059 AND 3060
HALL-EFFECT
GEAR-TOOTH SENSORS
—AC COUPLED
3059 AND
3060
HALL-EFFECT GEAR-TOOTH SENSORS
—AC COUPLED
XX
VCC
12 34 5
Dwg. PH-011
Pinning is shown viewed from branded side.
ABSOLUTE MAXIMUM RATINGS
at TA = +25°C
Supply Voltage, VCC ............................. 24 V
Reverse Battery Voltage, VRCC .......... -30 V
Magnetic Flux Density, B ............ Unlimited
Output OFF Voltage, VOUT .................... 24 V
Output Current, IOUT ......................... 25 mA
Package Power Dissipation,
PD ............................................ 500 mW
Operating Temperature Range, TA
Prefix ‘UGN’ ................. -20°C to +85°C
Prefix ‘UGS’ ............... -40°C to +125°C
Storage Temperature Range,
TS ............................... -65°C to +150°C
The UGN/UGS3059KA and UGN/UGS3060KA ac-coupled Hall-
effect gear-tooth sensors are monolithic integrated circuits that switch
in response to changing differential magnetic fields created by moving
ferrous targets. These devices are ideal for use in non-zero-speed,
gear-tooth-based speed, position, and timing applications such as in
anti-lock braking systems, transmissions, and crankshafts.
Both devices, when coupled with a back-biasing magnet, can be
configured to turn ON or OFF with the leading or trailing edge of a
gear-tooth or slot. Changes in fields on the magnet face caused by a
moving ferrous mass are sensed by two integrated Hall transducers
and are differentially amplified by on-chip electronics. This differential
sensing design provides immunity to radial vibration within the devices’
operating air gaps. Steady-state magnet and system offsets are
eliminated using an on-chip differential band-pass filter. This filter also
provides relative immunity to interference from RF and electromag-
netic sources. The on-chip temperature compensation and Schmitt
trigger circuitry minimizes shifts in effective working air gaps and
switch points over temperature, allowing operation to low frequencies
over a wide range of air gaps and temperatures.
Each Hall-effect digital Integrated circuit includes a voltage regu-
lator, two quadratic Hall-effect sensing elements, temperature com-
pensating circuitry, a low-level amplifier, band-pass filter, Schmitt
trigger, and an open-collector output driver. The on-board regulator
permits operation with supply voltages of 4.5 to 24 volts. The output
stage can easily switch 20 mA over the full frequency response range
of the sensor and is compatible with bipolar and MOS logic circuits.
The two devices provide a choice of operating temperature
ranges. Both devices are packaged in a 5-pin plastic SIP.
FEATURES
s Senses Motion of Ferrous
s Large Effective Air Gap
Targets Such as Gears
s 4.5 V to 24 V Operation
s Wide Operating Temperature Range s Output Compatible With
s Operation to 30 kHz
All Logic Families
s Resistant to RFI, EMI
s Reverse Battery Protection
s Resistant to Physical Stress
Always order by complete part number, e.g., UGS3060KA .

PagesPages 8
Télécharger [ 3059 ]


Fiche technique recommandé

No Description détaillée Fabricant
3050PT Phase Control Thyristors nELL
nELL
3052-xxx PC BOard Mountable Accelerometer IC Sensors
IC Sensors
3052P SI-3052P Sanken electric
Sanken electric
3054 MULTIPLEXED TWO-WIRE HALL-EFFECT SENSOR ICs Allegro MicroSystems
Allegro MicroSystems

US18650VTC5A

Lithium-Ion Battery

Sony
Sony
TSPC106

PCI Bus Bridge Memory Controller

ATMEL
ATMEL
TP9380

NPN SILICON RF POWER TRANSISTOR

Advanced Semiconductor
Advanced Semiconductor


www.DataSheetWiki.com    |   2020   |   Contactez-nous  |   Recherche