DataSheetWiki


A29040 fiches techniques PDF

AMIC Technology - 512K X 8 Bit CMOS 5.0 Volt-only/ Uniform Sector Flash Memory

Numéro de référence A29040
Description 512K X 8 Bit CMOS 5.0 Volt-only/ Uniform Sector Flash Memory
Fabricant AMIC Technology 
Logo AMIC Technology 





1 Page

No Preview Available !





A29040 fiche technique
A29040A Series
Preliminary
512K X 8 Bit CMOS 5.0 Volt-only,
Uniform Sector Flash Memory
Features
n 5.0V ± 10% for read and write operations
n Access times:
- 55/70/90 (max.)
n Current:
- 20 mA typical active read current
- 30 mA typical program/erase current
- 1 µA typical CMOS standby
n Flexible sector architecture
- 8 uniform sectors of 64 Kbyte each
- Any combination of sectors can be erased
- Supports full chip erase
- Sector protection:
A hardware method of protecting sectors to prevent
any inadvertent program or erase operations within
that sector
n Embedded Erase Algorithms
- Embedded Erase algorithm will automatically erase
the entire chip or any combination of designated
sectors and verify the erased sectors
General Description
The A29040A is a 5.0 volt-only Flash memory organized as
524,288 bytes of 8 bits each. The 512 Kbytes of data are
further divided into eight sectors of 64 Kbytes each for flexible
sector erase capability. The 8 bits of data appear on I/O0 - I/O7
while the addresses are input on A0 to A18. The A29040A is
offered in 32-pin PLCC, TSOP, and PDIP packages. This
device is designed to be programmed in-system with the
standard system 5.0 volt VCC supply. Additional 12.0 volt VPP
is not required for in-system write or erase operations.
However, the A29040A can also be programmed in standard
EPROM programmers.
The A29040A has a second toggle bit, I/O2, to indicate
whether the addressed sector is being selected for erase, and
also offers the ability to program in the Erase Suspend mode.
The standard A29040A offers access times of 55, 70 and 90
ns, allowing high-speed microprocessors to operate without
wait states. To eliminate bus contention the device has
separate chip enable ( CE ), write enable ( WE ) and output
enable ( OE ) controls.
The device requires only a single 5.0 volt power supply for
both read and write functions. Internally generated and
regulated voltages are provided for the program and erase
operations.
- Embedded Program algorithm automatically writes
and verifies bytes at specified addresses
n Typical 100,000 program/erase cycles per sector
n 20-year data retention at 125°C
- Reliable operation for the life of the system
n Compatible with JEDEC-standards
- Pinout and software compatible with single-power-
supply Flash memory standard
- Superior inadvertent write protection
n Data Polling and toggle bits
- Provides a software method of detecting completion
of program or erase operations
n Erase Suspend/Erase Resume
- Suspends a sector erase operation to read data from,
or program data to, a non-erasing sector, then
resumes the erase operation
n Package options
- 32-pin P-DIP, PLCC, or TSOP (Forward type)
The A29040A is entirely software command set compatible
with the JEDEC single-power-supply Flash standard.
Commands are written to the command register using
standard microprocessor write timings. Register contents
serve as input to an internal state-machine that controls the
erase and programming circuitry. Write cycles also internally
latch addresses and data needed for the programming and
erase operations. Reading data out of the device is similar to
reading from other Flash or EPROM devices.
Device programming occurs by writing the proper program
command sequence. This initiates the Embedded Program
algorithm - an internal algorithm that automatically times the
program pulse widths and verifies proper program margin.
Device erasure occurs by executing the proper erase
command sequence. This initiates the Embedded Erase
algorithm - an internal algorithm that automatically
preprograms the array (if it is not already programmed)
before executing the erase operation. During erase, the
device automatically times the erase pulse widths and
verifies proper erase margin.
PRELIMINARY (August, 2001, Version 0.1)
1
AMIC Technology, Inc.

PagesPages 30
Télécharger [ A29040 ]


Fiche technique recommandé

No Description détaillée Fabricant
A29040 512K X 8 Bit CMOS 5.0 Volt-only/ Uniform Sector Flash Memory AMIC Technology
AMIC Technology
A29040-120 512K X 8 Bit CMOS 5.0 Volt-only/ Uniform Sector Flash Memory AMIC Technology
AMIC Technology
A29040-150 512K X 8 Bit CMOS 5.0 Volt-only/ Uniform Sector Flash Memory AMIC Technology
AMIC Technology
A29040-55 512K X 8 Bit CMOS 5.0 Volt-only/ Uniform Sector Flash Memory AMIC Technology
AMIC Technology

US18650VTC5A

Lithium-Ion Battery

Sony
Sony
TSPC106

PCI Bus Bridge Memory Controller

ATMEL
ATMEL
TP9380

NPN SILICON RF POWER TRANSISTOR

Advanced Semiconductor
Advanced Semiconductor


www.DataSheetWiki.com    |   2020   |   Contactez-nous  |   Recherche