ACT-F128K32N-120P3I Datasheet PDF - Aeroflex Circuit Technology
| Part Number | ACT-F128K32N-120P3I | |
| Description | ACT-F128K32 High Speed 4 Megabit FLASH Multichip Module | |
| Manufacturers | Aeroflex Circuit Technology | |
| Logo |  |
|
|
There is a preview and ACT-F128K32N-120P3I download ( pdf file ) link at the bottom of this page. Total 20 Pages | ||
Preview 1 page No Preview Available !
ACT–F128K32 High Speed
4 Megabit FLASH Multichip Module
Features
CIRCUIT TECHNOLOGY
www.aeroflex.com
s 4 Low Power 128K x 8 FLASH Die in One MCM
Package
s Organized as 128K x 32
q User Configurable to 256K x 16 or 512K x 8
q Upgradable to 512K x 32 in same Package Style
s Access Times of 60, 70, 90, 120 and 150ns
s +5V Programing, 5V ±10% Supply
s 100,000 Erase/Program Cycles Typical, 0°C to +70°C
s Low Standby Current
s TTL Compatible Inputs and CMOS Outputs
s Embedded Erase and Program Algorithms
s Page Program Operation and Internal Program
Control Time
s Commercial, Industrial and Military Temperature
Ranges
s MIL-PRF-38534 Compliant MCMs Available
s Industry Standard Pinouts
s Packaging – Hermetic Ceramic
q 68 Lead, .88" x .88" x .160" Single-Cavity Small
Outline gull wing, Aeroflex code# "F5" (Drops into
the 68 Lead JEDEC .99"SQ CQFJ footprint)
q 66 Pin, 1.08" x 1.08" x .160" PGA Type, No
Shoulder, Aeroflex code# "P3"
q 66 Pin, 1.08" x 1.08" x .185" PGA Type, With
Shoulder, Aeroflex code# "P7"
s Sector Architecture (Each Die)
q 8 Equal size sectors of 64K bytes each
q Any Combination of Sectors can be erased with
one command sequence
q Supports Full Chip Erase
s DESC SMD# 5962–94716 Released (P3,P7,F5)
Block Diagram – PGA Type Package(P3,P7) & CQFP(F5)
WE1 CE1 WE2 CE2 WE3 CE3 WE4 CE4
OE
A0–A16
128Kx8 128Kx8 128Kx8 128Kx8
8
I/O0-7
88
8
I/O8-15 I/O16-23 I/O24-31
Pin Description
I/O0-31 Data I/O
A0–16 Address Inputs
WE1-4 Write Enables
CE1-4 Chip Enables
OE Output Enable
VCC Power Supply
GND
Ground
NC Not Connected
General Description
The ACT–F128K32 is a high
speed, 4 megabit CMOS flash
multichip module (MCM)
designed for full temperature
range military, space, or high
reliability applications.
The MCM can be organized
as a 128K x 32 bits, 256K x 16
bits or 512K x 8 bits device and
is input TTL and output CMOS
compatible. The command
register is written by bringing
WE to a logic low level (VIL),
while CE is low and OE is at
logic high level (VIH). Reading is
accomplished by chip Enable
(CE) and Output Enable (OE)
being logically active, see
Figure 9. Access time grades of
60ns, 70ns, 90ns, 120ns and
150ns maximum are standard.
The ACT–F128K32 is
packaged in a hermetically
eroflex Circuit Technology - Advanced Multichip Modules © SCD1667 REV A 4/28/98
|
| |
 
Device Operation
The ACT-F128K32 MCM is composed of four, one
megabit flash EEPROMs. The following description is for
the individual flash EEPROM device, is applicable to
each of the four memory chips inside the MCM. Chip 1 is
distinguished by CE1 and I/O1-7, Chip 2 by CE2 and
I/08-15, Chip 3 by CE3 and I/016-23, and Chip 4 by CE4 and
I/024-31.
Programming of the ACT-F128K32 is accomplished by
executing the program command sequence. The
program algorithm, which is an internal algorithm,
automatically times the program pulse widths and verifies
proper cell status. Sectors can be programed and
verified in less than 0.3 second. Erase is accomplished
by executing the erase command sequence. The erase
algorithm, which is internal, automatically preprograms
the array if it is not already programed before executing
the erase operation. During erase, the device
automatically times the erase pulse widths and verifies
proper cell status. The entire memory is typically erased
and verified in 3 seconds (if pre-programmed). The
sector mode allows for 16K byte blocks of memory to be
erased and reprogrammed without affecting other blocks.
Bus Operation
READ
The ACT-F128K32 has two control functions, both of
which must be logically active, to obtain data at the
outputs. Chip Enable (CE) is the power control and
should be used for device selection. Output-Enable (OE)
is the output control and should be used to gate data to
the output pins of the chip selected. Figure 7 illustrates
AC read timing waveforms.
OUTPUT DISABLE
With Output-Enable at a logic high level (VIH), output from
the device is disabled. Output pins are placed in a high
impedance state.
STANDBY MODE
The ACT-F128K32 has two standby modes, a CMOS
standby mode (CE input held at Vcc + 0.5V), where the
Table 1 – Bus Operations
Operation
CE OE WE A0 A1 A9 I/O
READ
L L H A0 A1 A9 DOUT
STANDBY
H X X X X X HIGH Z
OUTPUT DISABLE L H H X X X HIGH Z
WRITE
L H L A0 A1 A9 DIN
ENABLE SECTOR
PROTECT
L VID L
X
X VID
X
VERIFY SECTOR
PROTECT
L
L
H
L
H VID Code
current consumed is typically less than 400 µA; and a
TTL standby mode (CE is held VIH) is approximately 1
mA. In the standby mode the outputs are in a high
impedance state, independent of the OE input.
If the device is deselected during erasure or
programming, the device will draw active current until the
operation is completed.
WRITE
Device erasure and programming are accomplished via
the command register. The contents of the register serve
as input to the internal state machine. The state machine
outputs dictate the function of the device.
The command register itself does not occupy an
addressable memory location. The register is a latch
used to store the command, along with address and data
information needed to execute the command. The
command register is written by bringing WE to a logic low
level (VIL), while CE is low and OE is at VIH. Addresses
are latched on the falling edge of WE or CE, whichever
happens later. Data is latched on the rising edge of the
WE or CE whichever occurs first. Standard
microprocessor write timings are used. Refer to AC
Program Characteristics and Waveforms, Figures 3,
8 and 13.
Command Definitions
Device operations are selected by writing specific
address and data sequences into the command register.
Table 3 defines these register command sequences.
READ/RESET COMMAND
The read or reset operation is initiated by writing the
read/reset command sequence into the command
register. Microprocessor read cycles retrieve array data
from the memory. The device remains enabled for reads
until the command register contents are altered.
The device will automatically power-up in the read/reset
state. In this case, a command sequence is not required
to read data. Standard microprocessor read cycles will
retrieve array data. The device will automatically
power-up in the read/reset state. In this case, a command
sequence is not required to read data. Standard
Microprocessor read cycles will retrieve array data. This
Table 2 – Sector Addresses Table
A16 A15 A14
SA0 0 0 0
SA1 0 0 1
SA2 0 1 0
SA3 0 1 1
SA4 1 0 0
SA5 1 0 1
SA6 1 1 0
SA7 1 1 1
Address Range
00000h – 03FFFh
04000h – 07FFFh
08000h – 0BFFFh
0C000h – 0FFFFh
10000h – 13FFFh
14000h – 17FFFh
18000h – 1BFFFh
1C000h – 1FFFFh
Aeroflex Circuit Technology
5 SCD1667 REV A 4/28/97 Plainview NY (516) 694-6700
Preview 5 Page |
Part DetailsOn this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for ACT-F128K32N-120P3I electronic component. |
| Information | Total 20 Pages | |
| Link URL | [ Copy URL to Clipboard ] | |
| Download | [ ACT-F128K32N-120P3I.PDF Datasheet ] | |
Share Link :
Electronic Components Distributor
|
An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists. |
| SparkFun Electronics | Allied Electronics | DigiKey Electronics | Arrow Electronics |
| Mouser Electronics | Adafruit | Newark | Chip One Stop |
Featured Datasheets
| Part Number | Description | MFRS |
| ACT-F128K32N-120P3C | The function is ACT-F128K32 High Speed 4 Megabit FLASH Multichip Module. Aeroflex Circuit Technology | |
| ACT-F128K32N-120P3I | The function is ACT-F128K32 High Speed 4 Megabit FLASH Multichip Module. Aeroflex Circuit Technology | |
| ACT-F128K32N-120P3M | The function is ACT-F128K32 High Speed 4 Megabit FLASH Multichip Module. Aeroflex Circuit Technology | |
Semiconductors commonly used in industry:
1N4148 |
BAW56 |
1N5400 |
NE555 | | ||
Quick jump to:
ACT-
1N4
2N2
2SA
2SC
74H
BC
HCF
IRF
KA | ||