|
|
PDF ADS901 Data sheet ( Hoja de datos )
| Número de pieza | ADS901 | |
| Descripción | 10-Bit/ 20MHz/ #V Supply ANALOG-TO-DIGITAL CONVERTER | |
| Fabricantes | Burr-Brown Corporation | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de ADS901 (archivo pdf) en la parte inferior de esta página. Total 11 Páginas | ||
|
No Preview Available !
®
ADS901E
ADS901
10-Bit, 20MHz, +3V Supply
TM
ANALOG-TO-DIGITAL CONVERTER
FEATURES
q LOW POWER: 48mW at +3V
q SUPPLY RANGE: +2.7V to +3.7V
q ADJUSTABLE FULL SCALE RANGE WITH
EXTERNAL REFERENCES
q NO MISSING CODES
q WIDEBAND TRACK/HOLD: 350MHz
q POWER DOWN: 15mW
q 28-LEAD SSOP PACKAGE
APPLICATIONS
q BATTERY POWERED EQUIPMENT
q CAMCORDERS
q DIGITAL CAMERAS
q COMPUTER SCANNERS
q COMMUNICATIONS
ADS901
DESCRIPTION
The ADS901 is a high-speed pipelined analog-to-
digital converter that operates from a +3V power
supply. This complete converter includes a wide band-
width track/hold and a 10-bit quantizer. The full scale
input range is set by external references.
The ADS901 employs digital error correction tech-
niques to provide excellent differential linearity for
demanding imaging applications. Its low distortion
and high SNR give the extra margin needed for
telecommunications, video and test instrumentation
applications. The ADS901 is available in a 28-lead
SSOP package.
CLK
Timing
Circuitry
LVDD
IN T/H
Pipeline
A/D
Error
Correction
Logic
3-State
Outputs
10-Bit
Digital
Data
Reference
Ladder
REFT CM REFB
Pwrdn OE
International Airport Industrial Park • Mailing Address: PO Box 11400, Tucson, AZ 85734 • Street Address: 6730 S. Tucson Blvd., Tucson, AZ 85706 • Tel: (520) 746-1111
Twx: 910-952-1111 • Internet: http://www.burr-brown.com/ • Cable: BBRCORP • Telex: 066-6491 • FAX: (520) 889-1510 • Immediate Product Info: (800) 548-6132
©1997 Burr-Brown Corporation
PDS-1340C
Printed in U.S.A. June, 1999
1 page  
TYPICAL PERFORMANCE CURVES
At TA = +25°C, VS = Logic VDD = +3V, REFB = 1V, REFT = 2V, Specified Input Range = 1V to 2V, Sampling Rate = 20MHz, unless otherwise specified.
0
–20
–40
–60
–80
–100
0
SPECTRAL PERFORMANCE
fIN = 500kHz
2 4 68
Frequency (MHz)
10
0
–20
–40
–60
–80
–100
0
SPECTRAL PERFORMANCE
fIN = 3.58MHz
2 4 68
Frequency (MHz)
10
0
–20
–40
–60
–80
–100
0
SPECTRAL PERFORMANCE
fIN = 9MHz
2 4 68
Frequency (MHz)
10
0
–20
–40
–60
–80
–100
0
TWO-TONE INTERMODULATION
f1 = 4.5MHz
f2 = 5.0MHz
2.5 5 7.5
Frequency (MHz)
10
2
1
0
–1
–2
0
DIFFERENTIAL LINEARITY ERROR
fIN = 500kHz
256 512 768
Output Code
1024
2
1
0
–1
–2
0
DIFFERENTIAL LINEARITY ERROR
fIN = 9MHz
256 512 768
Output Code
1024
®
5 ADS901
5 Page 
+VS
10kΩ
REF1004
+1.2V
5kΩ
3kΩ
+VS
1/2 A1
RF1
RG1
10Ω
Top
Reference
(REFT)
1/2 A1
10Ω
Bottom
Reference
(REFB)
RF2
RG2
A1 = OPA2237 or Equivalent.
FIGURE 6. Precise Solution to Supply External Reference
Voltages.
DIGITAL OUTPUTS
There is a 5.0 clock cycle data latency from the start convert
signal to the valid output data. The standard output coding
is Straight Offset Binary where a full scale input signal
corresponds to all “1’s” at the output. The digital outputs of
the ADS901 can be set to a high impedance state by driving
the three-state (pin 16) with a logic “HI”. Normal operation
is achieved with pin 16 “LO” or Floating due to internal
pull-down resistors. This function is provided for testability
purposes but is not recommended to be used dynamically.
The digital outputs of the ADS901 are standard CMOS
stages and designed to be compatible to both high speed
TTL and CMOS logic families. The logic thresholds are for
low-voltage CMOS: VOL = 0.4V, VOH = 2.4V, which allows
the ADS901 to directly interface to 3V-logic. The digital
outputs of the ADS901 use a dedicated digital supply pin
(pin 2, LVDD). By adjusting the voltage on LVDD, the digital
output levels will vary respectively. In any case, it is recom-
mended to limit the fan-out to one, to keep the capacitive
loading on the data lines below the specified 15pF. If
necessary, external buffers or latches may be used to provide
the added benefit of isolating the A/D converter from any
digital activities on the bus coupling back high frequency
noise and degrading the performance.
POWER-DOWN MODE
The ADS901’s low power consumption can be further
reduced by initiating a power down mode. For this, the
Pwrdn-Pin (Pin 17) must be tied to a logic “High” reducing
the current drawn from the supply by approximately 70%. In
normal operation the power-down mode is disabled by an
internal pull-down resistor (50kΩ).
+VS +LVDD
ADS901
Digital
Output
Stage
FIGURE 7. Independent Supply Connection for Output
Stage.
During power-down the digital outputs are set in 3-state.
With the clock applied, the converter does not accurately
process the sampled signal. After removing the power-down
condition the output data from the following 5 clock cycles
is invalid (data latency).
DECOUPLING AND GROUNDING
CONSIDERATIONS
The ADS901 converter have several supply pins, one of
which is dedicated to supply only the output driver. The
remaining supply pins are not, as is often the case, divided
into analog and digital supply pins since they are internally
connected on the chip. For this reason it is recommended to
treat the converter as an analog component and to power it
from the analog supply only. Digital supply lines often carry
high levels of noise which can couple back into the converter
and limit the achievable performance.
Because of the pipeline architecture, the converter also
generates high frequency transients and noise that are fed
back into the supply and reference lines. This requires that
the supply and reference pins be sufficiently bypassed.
Figure 8 shows the recommended decoupling scheme for the
analog supplies. In most cases 0.1µF ceramic chip capacitors
are adequate to keep the impedance low over a wide fre-
quency range. Their effectiveness largely depends on the
proximity to the individual supply pin. Therefore they should
be located as close to the supply pins as possible.
ADS901
+VS GND
1 13 14
+VS
18
GND
19 20
+VS
28
0.1µF
0.1µF
0.1µF
FIGURE 8. Recommended Bypassing for Analog Supply
Pins.
®
11 ADS901
11 Page | ||
| Páginas | Total 11 Páginas | |
| PDF Descargar | [ Datasheet ADS901.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| ADS900 | 10-Bit/ 20MHz/ #V Supply ANALOG-TO-DIGITAL CONVERTER | Burr-Brown Corporation |
| ADS900 | ADS900: SpeedPlus 10-Bit 20MHz +3V Supply Analog-To-Digital Converter (Rev. A) |  Texas Instruments |
| ADS900E | 10-Bit/ 20MHz/ #V Supply ANALOG-TO-DIGITAL CONVERTER | Burr-Brown Corporation |
| ADS901 | 10-Bit/ 20MHz/ #V Supply ANALOG-TO-DIGITAL CONVERTER | Burr-Brown Corporation |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |