XR16M680 Datasheet PDF - Exar
| Part Number | XR16M680 | |
| Description | 1.62V TO 3.63V HIGH PERFORMANCE UART | |
| Manufacturers | Exar | |
| Logo |  |
|
|
There is a preview and XR16M680 download ( pdf file ) link at the bottom of this page. Total 30 Pages | ||
Preview 1 page No Preview Available !
XR16M680
1.62V TO 3.63V HIGH PERFORMANCE UART WITH 32-BYTE FIFO
SEPTEMBER 2008
REV. 1.0.0
GENERAL DESCRIPTION
The XR16M6801 (M680) is an enhanced Universal
Asynchronous Receiver and Transmitter (UART) with
32 bytes of transmit and receive FIFOs, selectable
transmit and receive FIFO trigger levels, automatic
hardware and software flow control, and data rates of
up to 16 Mbps at 3.3V, 12.5 Mbps at 2.5V and 7.5
Mbps at 1.8V with 4X data sampling rate.
The Auto RS-485 Half-Duplex Direction control
feature simplifies both the hardware and software for
half-duplex RS-485 applications. In addition, the
Multidrop mode with Auto Address detection
increases the performance by simplifying the
software routines.
The Independent TX/RX Baud Rate Generator
feature allows the transmitter and receiver to operate
at different baud rates. Power consumption of the
M680 can be minimized by enabling the sleep mode
and PowerSave mode.
The M680 has a 16550 compatible register set that
provide users with operating status and control,
receiver error indications, and modem serial interface
controls. An internal loopback capability allows
onboard diagnostics. The M680 is available in 32-pin
QFN, 48-pin TQFP and 25-pin BGA packages. All
three packages offer both the 16 mode (Intel bus)
interface and the 68 mode (Motorola bus) interface
which allows easy integration with Motorola
processors.
NOTE: 1 Covered by U.S. Patent #5,649,122.
FEATURES
• Pin-to-pin compatible with XR16L580 in 32-QFN
and 48-TQFP packages
• Intel or Motorola Bus Interface select
• 16Mbps maximum data rate
• Selectable TX/RX trigger levels
• TX/RX FIFO Level Counters
• Independent TX/RX Baud Rate Generator
• Fractional Baud Rate Generator
• Auto RTS/CTS Hardware Flow Control
• Auto XON/XOFF Software Flow Control
• Auto RS-485 Half-Duplex Direction Control
• Multidrop mode w/ Auto Address Detect
• Sleep Mode with Automatic Wake-up
• PowerSave mode
• Infrared (IrDA 1.0 and 1.1) mode
• 1.62V to 3.63V supply operation
• Crystal oscillator or external clock input
APPLICATIONS
• Personal Digital Assistants (PDA)
• Cellular Phones/Data Devices
• Battery-Operated Devices
• Global Positioning System (GPS)
• Bluetooth
FIGURE 1. XR16M680 BLOCK DIAGRAM
PwrSave
A2:A0
D7:D0
IOR#
IOW# (R/W#)
CS#
INT (IRQ#)
RESET
(RESET#)
16/68#
Intel or
M o to ro la
Data Bus
Interface
UART
UART 32 Byte TX FIFO
Regs TX &
IR
RX ENDEC
BRG 32 Byte RX FIFO
Crystal Osc/Buffer
VCC
(1.62 to 3.63 V)
GND
TX, RX,
RTS#, CTS#,
DTR#, DSR#,
RI#, CD#
XTAL1
XTAL2
Exar Corporation 48720 Kato Road, Fremont CA, 94538 • (510) 668-7000 • FAX (510) 668-7017 • www.exar.com
|
| |
 
REV. 1.0.0
Pin Description
XR16M680
1.62V TO 3.63V HIGH PERFORMANCE UART WITH 32-BYTE FIFO
NAME
RX
RTS#
CTS#
DTR#
DSR#
CD#
RI#
32-QFN 48-TQFP 25-BGA
PIN#
PIN#
PIN#
TYPE
DESCRIPTION
6 7 E4 I UART Receive Data or infrared receive data. Normal receive data
input must idle at logic 1 condition. The infrared receiver idles at
logic 0. This input should be connected to VCC when not used.
21 32 B3 O UART Request-to-Send (active low) or general purpose output.
This output must be asserted prior to using auto RTS flow control,
see EFR[6], MCR[1] and IER[6].
24 38 A1 I UART Clear-to-Send (active low) or general purpose input. It can
be used for auto CTS flow control, see EFR[7], MSR[4] and IER[7].
This input should be connected to VCC when not used.
22 33
- O UART Data-Terminal-Ready (active low) or general purpose output.
25 39
- I UART Data-Set-Ready (active low) or general purpose input. This
input should be connected to VCC when not used.
26 40
- I UART Carrier-Detect (active low) or general purpose input. This
input should be connected to VCC when not used.
27 41
- I UART Ring-Indicator (active low) or general purpose input. This
input should be connected to VCC when not used.
ANCILLARY SIGNALS
XTAL1
10
XTAL2
11
PwrSave
9
14
15
13
16/68#
2
1
RESET
(RESET#)
23
35
VCC
GND
GND
28
13
Center
Pad
42
18
-
D5 I Crystal or external clock input.
- O Crystal or buffered clock output.
C4 I Power-Save (active high). This feature isolates the M680’s data bus
interface from the host preventing other bus activities that cause
higher power drain during sleep mode. See Sleep Mode with Auto
Wake-up and Power-Save Feature section for details. This pin does
not have an internal pull-down resistor. This input should be con-
nected to GND when not used.
B2 I Intel or Motorola Bus Select. When 16/68# pin is at logic 1, 16 or
Intel Mode, the device will operate in the Intel bus type of interface.
When 16/68# pin is at logic 0, 68 or Motorola mode, the device will
operate in the Motorola bus type of interface. This pin does not
have an internal pull-up or pull-down resistor.
A2 I When 16/68# pin is at logic 1 for Intel bus interface, this input
becomes RESET (active high). When 16/68# pin is at logic 0 for
Motorola bus interface, this input becomes RESET# (active low).
A 40 ns minimum active pulse on this pin will reset the internal reg-
isters and all outputs of the UART. The UART transmitter output will
be held at logic 1, the receiver input will be ignored and outputs are
reset during reset period (see UART Reset Conditions).
B1 Pwr 1.62V to 3.63V power supply.
E5 Pwr Power supply common, ground.
- Pwr The center pad on the backside of the QFN package is metallic and
should be connected to GND on the PCB. The thermal pad size on
the PCB should be the approximate size of this center pad and
should be solder mask defined. The solder mask opening should be
at least 0.0025" inwards from the edge of the PCB thermal pad.
5
Preview 5 Page |
Part DetailsOn this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for XR16M680 electronic component. |
| Information | Total 30 Pages | |
| Link URL | [ Copy URL to Clipboard ] | |
| Download | [ XR16M680.PDF Datasheet ] | |
Share Link :
Electronic Components Distributor
|
An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists. |
| SparkFun Electronics | Allied Electronics | DigiKey Electronics | Arrow Electronics |
| Mouser Electronics | Adafruit | Newark | Chip One Stop |
Featured Datasheets
| Part Number | Description | MFRS |
| XR16M680 | The function is 1.62V TO 3.63V HIGH PERFORMANCE UART. Exar | |
| XR16M681 | The function is 1.62V TO 3.63V UART. Exar | |
Semiconductors commonly used in industry:
1N4148 |
BAW56 |
1N5400 |
NE555 | | ||
Quick jump to:
XR16
1N4
2N2
2SA
2SC
74H
BC
HCF
IRF
KA | ||