DataSheetWiki


FPF2147 fiches techniques PDF

Fairchild Semiconductor - Full Function Load Switch

Numéro de référence FPF2147
Description Full Function Load Switch
Fabricant Fairchild Semiconductor 
Logo Fairchild Semiconductor 





1 Page

No Preview Available !





FPF2147 fiche technique
November 2008
FPF2140/42/43/44/46/47
Full Function Load Switch with Reverse Current Blockingtm
Features
„ 1.8 to 5.5V Input Voltage Range
„ Controlled Turn-On
„ 200mA and 400mA Current Limit Options
„ Undervoltage Lockout
„ Thermal Shutdown
„ <2µA Shutdown Current
„ Auto Restart
„ Fast Current limit Response Time
„ 5µs to Moderate Over Currents
„ 30ns to Hard Shorts
„ Fault Blanking
„ Reverse Current Blocking
„ Power Good Function
„ RoHS Compliant
Applications
„ PDAs
„ Cell Phones
„ GPS Devices
„ MP3 Players
„ Digital Cameras
„ Peripheral Ports
„ Hot Swap Supplies
General Description
The FPF2140/42/43/44/46/47 is a series of load switches which
provides full protection to systems and loads which may
encounter large current conditions. These devices contain a
0.12current-limited P-channel MOSFET which can operate
over an input voltage range of 1.8-5.5V. Internally, current is
prevented from flowing when the MOSFET is off and the output
voltage is higher than the input voltage. Switch control is by a
logic input (ON) capable of interfacing directly with low voltage
control signals. Each part contains thermal shutdown protection
which shuts off the switch to prevent damage to the part when a
continuous over-current condition causes excessive heating.
When the switch current reaches the current limit, the part
operates in a constant-current mode to prohibit excessive
currents from causing damage. For the FPF2140/42/44/46, if
the constant current condition still persists after 30ms, the part
will shut off the switch and pull the fault signal pin (FLAGB) low.
The FPF2140/44 have an auto-restart feature which will turn the
switch on again after 450ms if the ON pin is still active. The
FPF2142/46 do not have this auto-restart feature so the switch
will remain off until the ON pin is cycled. For the FPF2143/47, a
current limit condition will immediately pull the fault signal pin
low and the part will remain in the constant-current mode until
the switch current falls below the current limit. The minimum
current limit is 200mA for the FPF2140/42/43 while that for the
FPF2144/46/47 is 400mA.
These parts are available in a space-saving 6 pin 2X2 MLP
package.
BOTTOM
Ordering Information
Part
FPF2140
FPF2142
FPF2143
FPF2144
FPF2146
FPF2147
Current Limit
[mA]
200/300/400
200/300/400
200/300/400
400/600/800
400/600/800
400/600/800
Pin 1
Current Limit
Blanking Time
[ms]
15/30/60
15/30/60
0
15/30/60
15/30/60
0
TOP
Auto-Restart
Time
[ms]
225/450/900
NA
NA
225/450/900
NA
NA
©2008 Fairchild Semiconductor Corporation
FPF2140/42/43/44/46/47 Rev. I
1
ON Pin
Activity
Active HI
Active HI
Active HI
Active HI
Active HI
Active HI
www.fairchildsemi.com

PagesPages 13
Télécharger [ FPF2147 ]


Fiche technique recommandé

No Description détaillée Fabricant
FPF2140 Full Function Load Switch Fairchild Semiconductor
Fairchild Semiconductor
FPF2142 Full Function Load Switch Fairchild Semiconductor
Fairchild Semiconductor
FPF2143 Full Function Load Switch Fairchild Semiconductor
Fairchild Semiconductor
FPF2144 Full Function Load Switch Fairchild Semiconductor
Fairchild Semiconductor

US18650VTC5A

Lithium-Ion Battery

Sony
Sony
TSPC106

PCI Bus Bridge Memory Controller

ATMEL
ATMEL
TP9380

NPN SILICON RF POWER TRANSISTOR

Advanced Semiconductor
Advanced Semiconductor


www.DataSheetWiki.com    |   2020   |   Contactez-nous  |   Recherche