|
|
PDF M238HVN01.0 Data sheet ( Hoja de datos )
| Número de pieza | M238HVN01.0 | |
| Descripción | color TFT LCD | |
| Fabricantes | AUO | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de M238HVN01.0 (archivo pdf) en la parte inferior de esta página. Total 30 Páginas | ||
|
No Preview Available !
Product Specification
AU OPTRONICS CORPORATION
M238HVN01.0
( ) Preliminary Specification
(V) Final Specification
Module
Model Name
23.8” Color TFT-LCD
M238HVN01.0
Customer
Date
Approved by
Note: This Specification is subject to change
without notice.
Approved by
Date
Howard Lee
Jun 9, 2015
Prepared by
Date
CJ Huang
Jun 9, 2015
AU Optronics corporation
document versionF1o.2r TEKIDS Internal Use Only - Provided By roselin On 2015/10/151
1 page  
Product Specification
AU OPTRONICS CORPORATION
M238HVN01.0
1 Handling Precautions
1) Since polarizer is easily damaged, do not touch or press the surface of polorizer with hand.
2) Be sure to turn off power supply when inserting or disconnecting from input connector.
3) Wipe off water drop immediately. Long contact with water may cause discoloration or spots.
4) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.
5) Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface.
6) Since CMOS LSI is used in this module, take care of static electricity and insure human earth when
handling.
7) Do not open or modify the Module Assembly.
8) Do not press the reflector sheet at the back of the module to any directions.
9) In case a TFT-LCD Module has to be put back into the packing container slot after once it was taken
out from the container, do not press the center of the LED lightbar edge. Otherwise the TFT-LCD
Module may be damaged.
10) Insert or pull out the interface connector, be sure not to rotate nor tilt it of the TFT-LCD Module.
11) Do not twist nor bend the TFT -LCD Module even momentary. It should be taken into consideration
that no bending/twisting forces are applied to the TFT-LCD Module from outside. Otherwise the
TFT-LCD Module may be damaged.
12) Please avoid touching COF position while you are doing mechanical design.
13) When storing modules as spares for a long time, the following precaution is necessary: Store them in a
dark place. Do not expose the module to sunlight or fluorescent light. Keep the temperature between
5 and 35 at normal humidity.
14) Do not apply the same pattern for a long time, it will enhance relevant defect.
document versionF1o.2r TEKIDS Internal Use Only - Provided By roselin On 2015/10/155
5 Page 
Product Specification
AU OPTRONICS CORPORATION
M238HVN01.0
Note 2-7: Crosstalk measurement
Definition:
CT = Max. (CTH,CTV);
Where
a.Maximum Horizontal Crosstalk :
CTH = Max. (| YBL – YAL | / YAL × 100 %, | YBR – YAR | / YAR × 100 %);
Maximum Vertical Crosstalk:
CTV = Max. (| YBU – YAU | / YAU × 100 %, | YBD – YAD | / YAD × 100 %);
b. YAU, YAD, YAL, YAR = Luminance of measured location without Black pattern
YBU, YBD, YBL, YBR = Luminance of measured location with Black pattern
Note 2-8: Flicker measurement
a. Test pattern: It is listed as following.
Gray level = L0
Gray level = L127
R: Red, G: Green, B:Blue
b. Measured position: Center of screen (P5) & perpendicular to the screen (θ=Φ=0°)
document version 1.2
11
For TEKIDS Internal Use Only - Provided By roselin On 2015/10/15
11 Page | ||
| Páginas | Total 30 Páginas | |
| PDF Descargar | [ Datasheet M238HVN01.0.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| M238HVN01.0 | color TFT LCD | AUO |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |