|
|
Número de pieza | N57M5114 | |
Descripción | 32-tap Digital Potentiometer | |
Fabricantes | ON Semiconductor | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de N57M5114 (archivo pdf) en la parte inferior de esta página. Total 13 Páginas | ||
No Preview Available ! N57M5114
Product Preview
32‐tap Digital
Potentiometer (POT)
Description
The N57M5114 is a single digital POT designed as an electronic
replacement for mechanical potentiometers and trim pots. Ideal for
automated adjustments on high volume production lines, they are also
well suited for applications where equipment requiring periodic
adjustment is either difficult to access or located in a hazardous or
remote environment.
The N57M5114 contains a 32-tap series resistor array connected
between two terminals RH and RL. An up/down counter and decoder
that are controlled by three input pins, determines which tap is
connected to the wiper, RW. The wiper setting, stored in nonvolatile
memory, is not lost when the device is powered down and is
automatically reinstated when power is returned. The wiper can be
adjusted to test new system values without affecting the stored setting.
Wiper-control of the N57M5114 is accomplished with three input
control pins, CS, U/D, and INC. The INC input increments the wiper
in the direction which is determined by the logic state of the U/D input.
The CS input is used to select the device and also store the wiper
position prior to power down.
The digital POT can be used as a three-terminal resistive divider or
as a two-terminal variable resistor. Digital POTs bring variability and
programmability to a wide variety of applications including control,
parameter adjustments, and signal processing.
Features
• 32-position Linear Taper Potentiometer
• Non-volatile EEPROM Wiper Storage
• Low Standby Current
• Single Supply Operation: 2.5 V − 6.0 V
• Increment Up/Down Serial Interface
• Resistance Values: 10 kW, 50 kW and 100 kW
• Available in SOIC, TSSOP, MSOP and Space Saving
2 × 3 mm TDFN Packages
• These Devices are Pb-Free, Halogen Free/BFR Free and are RoHS
Compliant
Applications
• Automated Product Calibration
• Remote Control Adjustments
• Offset, Gain and Zero Control
• Tamper-proof Calibrations
• Contrast, Brightness and Volume Controls
• Motor Controls and Feedback Systems
• Programmable Analog Functions
This document contains information on a product under development. ON Semiconductor
reserves the right to change or discontinue this product without notice.
© Semiconductor Components Industries, LLC, 2016
August, 2016 − Rev. P0
1
www.onsemi.com
SOIC−8
V SUFFIX
CASE 751BD
MSOP−8
Z SUFFIX
CASE 846AD
TSSOP−8
Y SUFFIX
CASE 948AL
TDFN−8
VP2 SUFFIX
CASE 511AK
PIN CONFIGURATIONS
INC
U/D
RH
GND
1
VCC
CS
RL
RW
SOIC (V), MSOP (Z)
1
CS
VCC
INC
U/D
TSSOP (Y)
RL
RW
GND
RH
INC
U/D
RH
GND
1
TDFN (VP2)
(Top Views)
VCC
CS
RL
RW
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 9 of this data sheet.
Publication Order Number:
N57M5114/D
1 page N57M5114
Table 5. DC ELECTRICAL CHARACTERISTICS (VCC = +2.5 V to +6 V unless otherwise specified)
Symbol
Parameter
Conditions
Min Typ Max Units
POWER SUPPLY
VCC Operating Voltage Range
ICC1 Supply Current (Increment)
ICC2 Supply Current (Write)
ISB1 (Note 4) Supply Current (Standby)
VCC = 6 V, f = 1 MHz, IW = 0
VCC = 6 V, f = 250 kHz, IW = 0
Programming, VCC = 6 V
VCC = 3 V
CS = VCC − 0.3 V
U/D, INC = VCC − 0.3 V or GND
2.5
–
–
–
–
–
– 6.0
V
– 100 mA
– 50 mA
– 1000 mA
– 500 mA
− 1 mA
LOGIC INPUTS
IIH Input Leakage Current
IIL Input Leakage Current
VIH2 CMOS High Level Input Voltage
VIL2 CMOS Low Level Input Voltage
POTENTIOMETER CHARACTERISTICS
VIN = VCC
VIN = 0 V
2.5 V ≤ VCC ≤ 6 V
– – 10 mA
– – −10 mA
VCC x 0.7 – VCC + 0.3
V
−0.3
– VCC x 0.2
V
RPOT
Potentiometer Resistance
−10 Device
−50 Device
10 kW
50
−00 Device
100
Pot. Resistance Tolerance
±20 %
VRH Voltage on RH pin
VRL Voltage on RL pin
Resolution
0
VCC
V
0
VCC
V
3.2 %
INL Integral Linearity Error
0.5 LSB
DNL
Differential Linearity Error
0.25 LSB
RWI Wiper Resistance
IW
TCRPOT
TCRATIO
VN
CH/CL/CW
fc
Wiper Current
TC of Pot Resistance
Ratiometric TC
Noise
Potentiometer Capacitances
Frequency Response
VCC = 5 V, IW = 1 mA
VCC = 2.5 V, IW = 1 mA
100 kHz / 1 kHz
Passive Attenuator, 10 kW
70
150
−4.4
300
8/24
8/8/25
1.7
200
400
4.4
20
W
W
mA
ppm/°C
ppm/°C
nV/√Hz
pF
MHz
Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product
performance may not be indicated by the Electrical Characteristics if operated under different conditions.
3. This parameter is tested initially and after a design or process change that affects the parameter.
4. Latch−up protection is provided for stresses up to 100 mA on address and data pins from −1 V to VCC + 1 V.
5. IW = source or sink.
6. These parameters are periodically sampled and are not 100% tested.
www.onsemi.com
5
5 Page E E1
A A2
A1
TOP VIEW
D
N57M5114
PACKAGE DIMENSIONS
MSOP 8, 3x3
CASE 846AD
ISSUE O
SYMBOL
A
A1
A2
b
c
D
E
E1
e
L
L1
L2
θ
MIN
0.05
0.75
0.22
0.13
2.90
4.80
2.90
0.40
0º
NOM
0.10
0.85
3.00
4.90
3.00
0.65 BSC
0.60
0.95 REF
0.25 BSC
MAX
1.10
0.15
0.95
0.38
0.23
3.10
5.00
3.10
0.80
6º
e
SIDE VIEW
b
c
END VIEW
DETAIL A
Notes:
(1) All dimensions are in millimeters. Angles in degrees.
(2) Complies with JEDEC MO-187.
L
L1
DETAIL A
q
L2
www.onsemi.com
11
11 Page |
Páginas | Total 13 Páginas | |
PDF Descargar | [ Datasheet N57M5114.PDF ] |
Número de pieza | Descripción | Fabricantes |
N57M5114 | 32-tap Digital Potentiometer | ON Semiconductor |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |