DataSheetWiki


A2525 fiches techniques PDF

Allegro MicroSystems - USB POWER CONTROL SWITCHES

Numéro de référence A2525
Description USB POWER CONTROL SWITCHES
Fabricant Allegro MicroSystems 
Logo Allegro MicroSystems 





1 Page

No Preview Available !





A2525 fiche technique
2525 AND
2535
USB POWER CONTROL SWITCHES
A2525EM
The A2525EL/M and A2535EL/M are integrated high-side power
switches, optimized for self-powered and bus-powered Universal Serial
Bus (USB) applications. Few external components are necessary to
EN 1
8 OUT satisfy USB requirements. The A2525EL/EM ENABLE inputs are
FLG 2
7 IN
active high; the A2535EL/EM are active low.
All devices are ideally suited for USB applications. Each switch
GND 3
NC 6 NC
channel supplies up to 500 mA as required by USB peripheral devices.
NC 4 NC
NC 5 NC
YDwg. PP-070A
RNote that the A2525EM (DIP) and the
OA2525EL (SOIC) are electrically identical and
Tshare a common terminal number assignment.
FACABSOLUTE MAXIMUM RATINGS
Supply Voltage, VIN ..................... 6.0 V
TOutput Voltage, VOUT .................. 6.0 V
COutput Current,
IOUT ................. Internally Limited
AENABLE Voltage Range,
VEN ......................... –0.3 V to 10 V
TFault Flag Voltage, VFLG .............. 8.0 V
NFault Flag Current, IFLG ............. 50 mA
Package Power Dissipation,
OPD ................................. See Graph
Operating Temperature Range,
CTA .......................... -40°C to +85°C
In addition, the switch’s low on-resistance permits achieving the USB
voltage-drop requirements. Fault current is limited to typically
750 mA, satisfying the UL 25 VA safety requirements, and a flag
output is available to indicate a fault condition to the local USB
controller. Momentary voltage drops that may occur on the upstream
port when the switch is enabled in bus-powered applications is elimi-
nated by a “soft start” feature.
Additional features include thermal shutdown to prevent catastrophic
switch failure from high-current loads, undervoltage lockout to ensure
that the device remains OFF unless there is a valid input voltage
present, and 3.3 V and 5 V logic-compatible enable inputs.
These switches are provided in 8-pin mini-DIP (suffix ‘M’) and
8-lead SOIC (suffix ‘L’) packages.
Features
I 2.7 V to 5.8 V Input
I Up to 500 mA Continuous Load Current per Port
I 140 mMaximum ON-Resistance
I 1.25 A Maximum Short-Circuit Current Limit
I Individual Open-Drain Fault Flag Outputs
I 100 µA Typical ON-State Supply Current
I <1 µA Typical OFF-State Supply Current
I Outputs Can be Forced Higher Than Input (off-state)
I Thermal Shutdown
I 2.2 V Typical Undervoltage Lockout
I 0.6 ms Turn On (soft-start) and Fast Turn Off
Junction Temperature, TJ ....... +150°C*
Storage Temperature Range,
I A2525 (active-high) Improved Replacement for MIC2525-1
I A2535 (active-low) Improved Replacement for MIC2525-2
TS ........................... -65°C to 150°C
Applications
* Fault conditions that produce excessive
junction temperature will activate device
thermal shutdown circuitry. These conditions
can be tolerated but should be avoided.
I USB Hosts and Self-Powered Hubs
I USB Bus-Powered Hubs
I Hot Plug-In Power Supplies
I Battery-Charger Circuits

PagesPages 12
Télécharger [ A2525 ]


Fiche technique recommandé

No Description détaillée Fabricant
A2521 Grounded Grid Triode GEC
GEC
A2525 USB POWER CONTROL SWITCHES Allegro MicroSystems
Allegro MicroSystems
A2526 USB DUAL POWER CONTROL SWITCHES Allegro MicroSystems
Allegro MicroSystems

US18650VTC5A

Lithium-Ion Battery

Sony
Sony
TSPC106

PCI Bus Bridge Memory Controller

ATMEL
ATMEL
TP9380

NPN SILICON RF POWER TRANSISTOR

Advanced Semiconductor
Advanced Semiconductor


www.DataSheetWiki.com    |   2020   |   Contactez-nous  |   Recherche