DataSheetWiki


S25FL128P fiches techniques PDF

Cypress Semiconductor - 128-Mb 3.0 V Flash Memory

Numéro de référence S25FL128P
Description 128-Mb 3.0 V Flash Memory
Fabricant Cypress Semiconductor 
Logo Cypress Semiconductor 





1 Page

No Preview Available !





S25FL128P fiche technique
S25FL128P
128-Mb 3.0 V Flash Memory
This product is not recommended for new and current designs. For new and current designs, S25FL128S supersedes
S25FL128P. This is the factory-recommended migration path. Please refer to the S25FL128S data sheet for
specifications and ordering information.
Distinctive Characteristics
Architectural Advantages
Single power supply operation
– Full voltage range: 2.7V to 3.6V read and program operations
Memory Architecture
– 128Mb uniform 256 KB sector product
– 128Mb uniform 64 KB sector product
Program
– Page Program (up to 256 bytes) in 1.5 ms (typical)
– Faster program time in Accelerated Programming mode
(8.5 V–9.5 V on #WP/ACC) in 1.2 ms (typical)
Erase
– 2 s typical 256 KB sector erase time
– 0.5 s typical 64 KB sector erase time
– 128 s typical bulk erase time
– Sector erase (SE) command (D8h) for 256 KB sectors; (20h or
D8h) for 64KB sectors
– Bulk erase command (C7h) for 256 KB sectors; (60h or C7h) for
64KB sectors
Cycling Endurance
– 100,000 cycles per sector typical
Data Retention
– 20 years typical
Device ID
– RDID (9Fh), READ_ID (90h) and RES (ABh) commands to read
manufacturer and device ID information
– RES command one-byte electronic signature for backward
compatibility
Process Technology
– Manufactured on 0.09 µm MirrorBit® process technology
Package Option
– Industry Standard Pinouts
– 16-pin SO package (300 mils)
– 8-Contact WSON Package (6 x 8 mm)
Performance Characteristics
Speed
– 104 MHz clock rate (maximum)
Power Saving Standby Mode
– Standby Mode 200 µA (max)
– Deep Power Down Mode 3 µA (typical)
Memory Protection Features
Memory Protection
– WP#/ACC pin works in conjunction with Status Register Bits to
protect specified memory areas
– 256 KB uniform sector product:
Status Register Block Protection bits (BP2, BP1, BP0) in status
register configure parts of memory as read-only.
– 64KB uniform sector product:
Status Register Block Protection bits (BP3, BP2, BP1, BP0) in
status register configure parts of memory as read-only
Software Features
– SPI Bus Compatible Serial Interface
Hardware Features
x8 Parallel Programming Mode (for 16-pin SO package only)
General Description
The S25FL128P is a 3.0 Volt (2.7V to 3.6V), single-power-supply Flash memory device. The device consists of 64 sectors of
256 KB memory, or 256 sectors of 64 KB memory.
The device accepts data written to SI (Serial Input) and outputs data on SO (Serial Output). The devices are designed to be
programmed in-system with the standard system 3.0 volt VCC supply.
The memory can be programmed 1 to 256 bytes at a time, using the Page Program command. The device supports Sector Erase
and Bulk Erase commands.
Each device requires only a 3.0 volt power supply (2.7V to 3.6V) for both read and write functions. Internally generated and
regulated voltages are provided for the program operations. This device requires a high voltage supply to WP#/ACC pin for the
Accelerated Programming mode.
Cypress Semiconductor Corporation • 198 Champion Court
Document Number: 002-00646 Rev. *L
• San Jose, CA 95134-1709 • 408-943-2600
Revised September 18, 2015

PagesPages 30
Télécharger [ S25FL128P ]


Fiche technique recommandé

No Description détaillée Fabricant
S25FL128K 128-Mbit CMOS 3.0 Volt Flash Memory SPANSION
SPANSION
S25FL128P 128-Mb 3.0 V Flash Memory Cypress Semiconductor
Cypress Semiconductor
S25FL128P 128 Megabit CMOS 3.0 Volt Flash Memory SPANSION
SPANSION
S25FL128S 3.0V SPI Flash Memory Cypress
Cypress

US18650VTC5A

Lithium-Ion Battery

Sony
Sony
TSPC106

PCI Bus Bridge Memory Controller

ATMEL
ATMEL
TP9380

NPN SILICON RF POWER TRANSISTOR

Advanced Semiconductor
Advanced Semiconductor


www.DataSheetWiki.com    |   2020   |   Contactez-nous  |   Recherche