|
|
PDF ADG5404F Data sheet ( Hoja de datos )
| Número de pieza | ADG5404F | |
| Descripción | 4-Channel Multiplexer | |
| Fabricantes | Analog Devices | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de ADG5404F (archivo pdf) en la parte inferior de esta página. Total 30 Páginas | ||
|
No Preview Available !
Data Sheet
Fault Protection and Detection,
10 Ω RON, 4-Channel Multiplexer
ADG5404F
FEATURES
Overvoltage protection up to −55 V and +55 V
Power-off protection up to −55 V and +55 V
Overvoltage detection on source pins
Interrupt flags indicate fault status
Low on resistance: 10 Ω (typical)
On-resistance flatness of 0.5 Ω (maximum)
4 kV human body model (HBM) ESD rating
Latch-up immune under any circumstance
Known state without digital inputs present
VSS to VDD analog signal range
±5 V to ±22 V dual supply operation
8 V to 44 V single-supply operation
Fully specified at ±15 V, ±20 V, 12 V, and 36 V
APPLICATIONS
Analog input/output modules
Process control/distributed control systems
Data acquisition
Instrumentation
Avionics
Automatic test equipment
Communication systems
Relay replacement
GENERAL DESCRIPTION
The ADG5404F is an analog multiplexer composed of four
single channels with fault protected inputs. The ADG5404F
switches one of the four inputs to a common drain, D, as
determined by the 2-bit binary address lines (A0 and A1). An
enable digital input, EN, is used to disable all the switches. Each
channel conducts equally well in both directions when on, and
each switch has an input signal range that extends to the
supplies. The digital inputs are compatible with 3 V logic inputs
over the full operating supply range.
When no power supplies are present, the switch remains in the off
condition, and the channel inputs are high impedance. Under
normal operating conditions, if the analog input signal levels on
any Sx pin exceed VDD or VSS by a threshold voltage, VT, the
channel turns off and that Sx pin becomes high impedance. If
the channel is on, the drain pin reacts according to the drain
response (DR) input pin. If the DR pin is left floating or pulled
high, the drain remains high impedance and floats. If the DR pin
is pulled low, the drain pulls to the exceeded rail. Input signal
levels up to +55 V or −55 V relative to ground are blocked, in
both the powered and unpowered conditions.
Rev. B
Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibilityisassumedbyAnalogDevices for itsuse,nor foranyinfringementsofpatentsor other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarksandregisteredtrademarksarethepropertyoftheirrespectiveowners.
FUNCTIONAL BLOCK DIAGRAM
ADG5404F
S1
S2
D
S3
S4
FAULT
DETECTION
+ SWITCH
DRIVER
FF
SF
A0/F0 A1/F1 EN DR
Figure 1.
The low on resistance of the ADG5404F, combined with on-
resistance flatness over a significant portion of the signal range,
makes it an ideal solution for data acquisition and gain
switching applications where excellent linearity and low
distortion are critical.
Note that, throughout this data sheet, the dual function pin names
are referenced only by the relevant function where applicable. See
the Pin Configurations and Function Descriptions for full pin
names and function descriptions.
PRODUCT HIGHLIGHTS
1. Source pins are protected against voltages greater than the
supply rails, up to −55 V and +55 V.
2. Source pins are protected against voltages between −55 V
and +55 V in an unpowered state.
3. Overvoltage detection with digital output indicates
operating state of switches.
4. Trench isolation guards against latch-up.
5. Optimized for low on resistance and on-resistance flatness.
6. The ADG5404F operates from a dual supply of ±5 V up to
±22 V, or a single power supply of 8 V up to 44 V.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700 ©2014–2016 Analog Devices, Inc. All rights reserved.
Technical Support
www.analog.com
1 page  
Data Sheet
ADG5404F
±20 V DUAL SUPPLY
VDD = 20 V ± 10%, VSS = −20 V ± 10%, GND = 0 V, CDECOUPLING = 0.1 µF, unless otherwise noted.
Table 2.
Parameter
ANALOG SWITCH
Analog Signal Range
On Resistance, RON
On-Resistance Match Between Channels, ∆RON
On-Resistance Flatness, RFLAT(ON)
Threshold Voltage, VT
LEAKAGE CURRENTS
Source Off Leakage, IS (Off )
Drain Off Leakage, ID (Off )
Channel On Leakage, ID (On), IS (On)
FAULT
Source Leakage Current, IS
With Overvoltage
−40°C to −40°C to
+25°C +85°C
+125°C Unit
10
11.5 14.5
9.5
11 14
0.65
0.9 1.05
0.65
0.9 1.05
1.0
1.4 1.5
0.1
0.4 0.5
0.7
VDD to VSS
16.5
16.5
1.2
1.2
1.5
0.5
V
Ω typ
Ω max
Ω typ
Ω max
Ω typ
Ω max
Ω typ
Ω max
Ω typ
Ω max
Ω typ
Ω max
V typ
±0.1
±1.5 ±5.0
±0.3
±1.5 ±16.0
±0.3
±1.5 ±14.0
±21
±66
±56
nA typ
nA max
nA typ
nA max
nA typ
nA max
±85 µA typ
Power Supplies Grounded or Floating
±44 µA typ
Drain Leakage Current, ID
With Overvoltage
Power Supplies Grounded
Power Supplies Floating
DIGITAL INPUTS
Input Voltage High, VINH
Input Voltage Low, VINL
Input Current, IINL or IINH
Digital Input Capacitance, CIN
Output Voltage High, VOH
Output Voltage Low, VOL
±400
±1.5
±10
±30
±10
±1.5
±50
±10
0.7
6.0
2.0
0.8
±1.5
±100
±10
2.0
0.8
1.2
nA typ
µA max
nA typ
nA max
µA typ
V min
V max
µA typ
µA max
pF typ
V min
V max
Test Conditions/Comments
VDD = 18 V, VSS = −18 V, see Figure 31
VS = ±15 V, IS = −10 mA
VS = ±13.5 V, IS = −10 mA
VS = ±15 V, IS = −10 mA
VS = ±13.5 V, IS = −10 mA
VS = ±15 V, IS = −10 mA
VS = ±13.5 V, IS = −10 mA
See Figure 27
VDD = 22 V, VSS = −22 V
VS = ±15 V, VD = ±15 V, see Figure 32
VS = ±15 V, VD = ±15 V, see Figure 32
VS = VD = ±15 V, see Figure 33
VDD = +22 V, VSS = −22 V, GND = 0 V,
VS = ±55 V, see Figure 36
VDD = 0 V or floating, VSS = 0 V or floating,
GND = 0 V, INx = 0 V or floating, Ax = 0 V
or floating, VS = ±55 V, see Figure 37
DR = floating or >2 V
VDD = +22 V, VSS = −22 V, GND = 0 V,
VS = ±55 V, see Figure 36
VDD = 0 V, VSS = 0 V, GND = 0 V, VS =
±55 V, EN = 0 V, see Figure 37
VDD = floating, VSS = floating, GND =
0 V, VS = ±55 V, EN = 0 V, see Figure 37
VIN = VGND or VDD
Rev. B | Page 5 of 30
5 Page 
Data Sheet
CONTINUOUS CURRENT
Table 5.
Parameter
14-Lead TSSOP
θJA = 112.6°C/W
16-Lead LFCSP
θJA = 30.4°C/W
25°C
147
115
280
220
85°C
95
77
156
130
125°C
58
50
75
70
Unit
mA max
mA max
mA max
mA max
ADG5404F
Test Conditions/Comments
VS = VSS + 4.5 V to VDD − 4.5 V
VS = VSS to VDD
VS = VSS + 4.5 V to VDD − 4.5 V
VS = VSS to VDD
Rev. B | Page 11 of 30
11 Page | ||
| Páginas | Total 30 Páginas | |
| PDF Descargar | [ Datasheet ADG5404F.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| ADG5404 | 4-Channel Multiplexer | Analog Devices |
| ADG5404F | 4-Channel Multiplexer | Analog Devices |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |