|
|
PDF AOZ1935 Data sheet ( Hoja de datos )
| Número de pieza | AOZ1935 | |
| Descripción | High Efficiency Boost 20- or 30- LED Driver | |
| Fabricantes | Alpha & Omega Semiconductors | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de AOZ1935 (archivo pdf) en la parte inferior de esta página. Total 14 Páginas | ||
|
No Preview Available !
AOZ1934/1935
High Efficiency Boost 20-, 30- LED Driver
General Description
The AOZ1934/5 is an ideal power solution for white LED
backlighting for medium to small size LCD panels. It is a
highly integrated step up DC-DC converter with input
voltage range from 2.7V to 25V, accommodating
1-, 2-, 3-, or 4-cell lithium ion batteries or 3.3V, 5V, 12V
or 20V regulated supplies. The AOZ1934/5 integrates a
40V power MOSFET as well as compensation and soft
start circuitry, which results in a simpler and smaller
solution with much fewer external components. A high
switching frequency (800kHz) allows the use of a smaller
inductor and capacitor to further reduce the solution size.
Each of the regulated current sinks in the AOZ1934/5
provides 20mA factory programmed current. With a
maximum of 40V at the output of the step-up converter,
each string can connect up to ten LEDs in series, for a
total of 20 LEDs for AOZ1934 and 30 LEDs for AOZ1935.
The AOZ1934/5 is equipped with fast PWM dimming
control for wide dimming range and has an enable pin for
IC ON/OFF control. Various protection features are built
into the AOZ1934/5, including cycle-by-cycle input
current limit protection, output over-voltage protection,
LED fault (open or short) protection and thermal
shutdown protection. The leakage current in shutdown
mode is 0.1µA.
The AOZ1934/5 is available in a 16-lead 3 x 3 x 0.75mm
thin QFN package.
Features
z Wide input range: 2.7V to 25V
z Drive up to 30 LEDs
– AOZ1934 up to 20 LEDs (10s2p)
– AOZ1935 up to 30 LEDs (10s3p)
z Up to 92% efficiency
z High frequency step-up converter (800kHz)
z Highly integrated solution
– Integrated 40V Power MOSFET
– Internal compensation and soft start
z Integrated current sinks:
AOZ1934 – 2 channels, AOZ1935 – 3 channels
– ±2% Typ. current accuracy
– 1.5% Typ. current matching
z PWM dimming with <1µs delay time
z Low operating quiescent current (500µA)
z LED open/short protection
z Both internal fixed and external adjustable
Over-voltage protection
z Cycle-by-cycle inductor current limit (2.5A)
z 0.1µA shutdown current
z Green Package: 3 x 3 QFN-16
z -40°C to +85°C temperature range
Applications
z Netbook
z Tablet PCs
z GPS
z Portable media players
z 1-, 2-, 3-, 4-cell Li Ion LED applications
Rev. 1.0 August 2010
www.aosmd.com
Page 1 of 14
1 page  
AOZ1935
Absolute Maximum Ratings (TA=25°C unless otherwise noted(1)
Exceeding the Absolute Maximum ratings may damage the device.
Symbol
Description
Value
Unit
VIN
AVCC
LX, Sx
VOUT
EN, PWM, OV
TJ
TS
TLEAD
ESD
Boost Converter Input Voltage
IC Input Voltage
High Voltage Nodes
Output Voltage Node
Input Nodes
Operating Temperature Range
Storage Temperature Range
Maximum Soldering Temperature (at leads, 10 seconds)
Human Body Model
-0.3 to 28
-0.3 to 6
-0.3 to 44
-0.3 to 44
-0.3 to AVCC+0.3
-40 to 150
-65 to 150
300
2
V
V
V
V
°C
°C
°C
kV
Note:
1.Stresses above those listed in Absolute Maximum Ratings may cause permanent damage to the device. Functional operation at conditions other
than the operating conditions specified is not implied. Only one Absolute Maximum rating should be applied at any one time.
Thermal Capabilities
Symbol
Description
Value
Unit
ΘJA
PD
PD / ΔT
Thermal Resistance – Junction to Ambient(2)
Maximum Power Dissipation at TA ≤ 25°C
Derating Factor Above TA = 25°C
50 °C/W
2.0 W
-20 mW/°C
Note:
2. Junction to Ambient thermal resistance is highly dependent on PCB layout. Values are based on thermal properties of the device when soldered to
an EV board.
Rev. 1.0 August 2010
www.aosmd.com
Page 5 of 14
5 Page 
AOZ1935
Detailed Description
The AOZ1934/5 is a unique current regulated step-up
(boost) converter. Two (or three for AOZ1935) current
regulating devices are integrated to drive two or three
strings of LEDs. Unused channels need to be connected
to ground (GND).
The voltage step-up is accomplished by a boost topology,
using an inductor-based DC-DC switching converter, in
which the inductor serves as an energy storage device in
the system. By integrating a high voltage optimized
MOSFET, the AOZ1934/5 internal switching frequency is
800kHz while still maintaining high power efficiency.
Unlike a traditional DC-DC boost converter with a fixed
output voltage, the AOZ1934/5 dynamically changes its
output voltage regulation parameters depending on the
load. The use of unique control schemes maintains
accurate current regulation in each current sink while
leaving the output voltage at a minimum, increasing the
overall conversion efficiency. The internal step-up
converter dynamically controls the voltage at the output
high enough to drive the LED string with the highest total
forward voltage. The wide input voltage range, from 2.7V
to 25V, allows maximum system flexibility; battery
powered devices using 1-, 2-, 3- or 4-cell Li Ion packs
can share the same power architecture. A low power
2.7V to 5.5V input to supply the IC bias circuitry is
required at AVCC pin.
LED brightness control is based on the popular PWM
dimming scheme via the PWM pin. The EN pin provides
ON/OFF control of the IC. By asserting a logic high on
the EN pin, the converter is enabled and will regulate
each of the current sinks at the factory programmed
current setting.
Application Information
Power Up Sequence
It’s recommended to power up Vin, AVCC, and PWM
dimming in sequence, and EN pin needs to ramp up
simultaneously or later than AVCC, in order to avoid
latch-off, or mis-operation of device. We do not assume
any liability or responsibility for any loss or damage
arising from misuse or inappropriate use of the product.
Current Dimming Using PWM Pin
AOZ1934/5 allows maximum flexibility with a PWM signal
control input which can be used for dimming. The IC
must remain Enabled at EN pin during PWM dimming,
which means the step-up converter is active to reduce
the response time. Combining this with the fast response
of the step-up converter, each LED channel can typically
recover from no current within 1µs. This allows very short
PWM on-time or a duty-cycle with fine resolution.
Assume a 50µs minimum on-time for a 100Hz PWM
signal, a 200:1 ratio can be achieved by PWM.
The minimum PWM on-time of 1μs is required in
AOZ1934/5’s application, this means minimum PWM
duty cycle of 2% for 20kHz dimming frequency and
0.02% for 200Hz dimming frequency. The amplitude of
PWM signal should not be higher than AVCC, otherwise
test mode will be triggered.
Fault Protection (LED Open or Short)
Each current sink is protected against LED short or
open conditions. If an LED short circuit condition
arises, the current sink continues to regulate until
VSINK > VSOV (6V). When any sink node voltage goes
above VSOV for more than 80ms (while PWM dimming
signal remains high), that channel’s current sink will be
turned off, and other channels will still work if they don’t
trigger this fault condition. For example, if one or more
LEDs on a channel are shorted, that channel’s sink
voltage will increase. If the voltage goes above 6V for
more than 80ms, the Current Sink Fault Protection will be
triggered and only this faulty string will be disabled by
shutting off this current sink. All other channels will
continue normal operation if they don’t have a fault
condition. When PWM dimming control is used, the 80ms
fault delay is accumulated only when PWM signal is high;
the PWM low time is not counted into the fault delay, so
the delay time will be 80ms / DPWM (DPWM is the duty
cycle of the PWM signal).
In case of an LED failing open, the current sink voltage of
the failed string will go close to ground and dominate the
boost converter control loop. As a result the output
voltage will move up to the over-voltage threshold, set
internally to 40V or by the external resistor divider,
whichever is lower. Once the over-voltage incident is
flagged internally, the faulty channel(s) will be disabled.
Then the output voltage of the boost converter will go
back to normal level. During the entire process, the rest
of the LED strings (healthy LED strings) would continue
normal operation.
The fault conditions are reset when the IC is powered
down and up again.
Output Over-Voltage Protection (OVP)
AOZ1934/5 has built in over-voltage protection function
with 40V threshold at VOUT pin. This level is suitable for
applications with ten series LEDs per string. However, for
applications with fewer series LEDs, the user can choose
Rev. 1.0 August 2010
www.aosmd.com
Page 11 of 14
11 Page | ||
| Páginas | Total 14 Páginas | |
| PDF Descargar | [ Datasheet AOZ1935.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| AOZ1934 | High Efficiency Boost 20- or 30- LED Driver | Alpha & Omega Semiconductors |
| AOZ1935 | High Efficiency Boost 20- or 30- LED Driver | Alpha & Omega Semiconductors |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |